[root@ ~]# telnet 192.168.12.130 8890 Trying 192.168.12.130... Connected to 192.168.12.130. Escape character is '^]'. %IOSXEBOOT-4-WAIT_FOR_DEVICES: (local/local): Partition "/dev/bootflash1" missing at 20180429013632 Continuing to initialization %IOSXEBOOT-4-PART_INVALID: (local/local): /dev/bootflash has an invalid partition table that must be repaired. %IOSXEBOOT-4-PART_REPAIR: (local/local): The system will repair /dev/bootflash now. %IOSXEBOOT-4-PART_REPAIR: (local/local): This may cause loss of data and configuration on /dev/bootflash. %IOSXEBOOT-4-PART_REPAIR_FINISHED: (local/local): Partitioning complete. %IOSXEBOOT-4-PART_SEEDNVRAM: (local/local): Seeding nvram [SUCCESS] %IOSXEBOOT-4-FILESYS_INVALID: (local/local): partition /dev/bootflash1 has an invalid filesystem that must be re-initialized. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): The system will repair /dev/bootflash1 now. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): This will cause a complete loss of data. %IOSXEBOOT-4-FILESYS_INVALID: (local/local): partition /dev/bootflash5 has an invalid filesystem that must be re-initialized. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): The system will repair /dev/bootflash5 now. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): This will cause a complete loss of data. %IOSXEBOOT-4-FILESYS_INVALID: (local/local): partition /dev/bootflash6 has an invalid filesystem that must be re-initialized. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): The system will repair /dev/bootflash6 now. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): This will cause a complete loss of data. %IOSXEBOOT-4-FILESYS_INVALID: (local/local): partition /dev/bootflash7 has an invalid filesystem that must be re-initialized. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): The system will repair /dev/bootflash7 now. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): This will cause a complete loss of data. %IOSXEBOOT-4-FILESYS_INVALID: (local/local): partition /dev/bootflash8 has an invalid filesystem that must be re-initialized. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): The system will repair /dev/bootflash8 now. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): This will cause a complete loss of data. %IOSXEBOOT-4-FILESYS_INVALID: (local/local): partition /dev/bootflash9 has an invalid filesystem that must be re-initialized. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): The system will repair /dev/bootflash9 now. %IOSXEBOOT-4-FILESYS_REPAIR: (local/local): This will cause a complete loss of data. %IOSXEBOOT-4-BOOT_SRC: (rp/0): CD-ROM Boot %IOSXEBOOT-4-BOOT_CDROM: (rp/0): Using Serial console %IOSXEBOOT-4-BOOT_CDROM: (rp/0): Installing GRUB to /dev/bootflash %IOSXEBOOT-4-BOOT_CDROM: (rp/0): Copying image to /boot %IOSXEBOOT-4-BOOT_CDROM: (rp/0): Copying image to /bootflash %IOSXEBOOT-4-BOOT_CDROM: (rp/0): Creating /boot/grub/menu.lst %IOSXEBOOT-4-BOOT_CDROM: (rp/0): Ejecting CD-ROM tray %IOSXEBOOT-4-BOOT_CDROM: (rp/0): CD-ROM Installation finished %IOSXEBOOT-4-BOOT_CDROM: (rp/0): Rebooting from HD Connection closed by foreign host. [root@ ~]# telnet 192.168.12.130 8890 Trying 192.168.12.130... Connected to 192.168.12.130. Escape character is '^]'. The highlighted entry will be booted automatically in 3 seconds. The highlighted entry will be booted automatically in 2 seconds. The highlighted entry will be booted automatically in 1 seconds. Booting 'CSR1000v - packages.conf' root (hd0,0) Filesystem type is ext2fs, partition type 0x83 kernel /packages.conf rw quiet root=/dev/ram console= max_loop=64 HARDWARE=virt ual SR_BOOT=bootflash:packages.conf Calculating SHA-1 hash...done SHA-1 hash: calculated ef2043b5:caad0265:2a268887:a7004ba8:fcfe6506 expected ef2043b5:caad0265:2a268887:a7004ba8:fcfe6506 package header rev 3 structure detected Calculating SHA-1 hash...done SHA-1 hash: calculated e674e45a:1da6da5e:2e3d73a7:7cf8b076:631b84d8 expected e674e45a:1da6da5e:2e3d73a7:7cf8b076:631b84d8 Package type:0x7531, flags:0x0 [Linux-bzImage, setup=0x3c00, size=0x4c5e00] [isord @ 0x7e032000, 0x1fbded6 bytes] %IOSXEBOOT-4-BOOT_SRC: (rp/0): Checking grub versions 1.0 vs 1.0 %IOSXEBOOT-4-BOOT_SRC: (rp/0): No need for bootloader upgrade. Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software [Fuji], Virtual XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.8.1a, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2018 by Cisco Systems, Inc. Compiled Tue 03-Apr-18 18:43 by mcpre PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR LICENSE KEY PROVIDED FOR ANY CISCO SOFTWARE PRODUCT, PRODUCT FEATURE, AND/OR SUBSEQUENTLY PROVIDED SOFTWARE FEATURES (COLLECTIVELY, THE "SOFTWARE"), AND/OR USING SUCH SOFTWARE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN. Your use of the Software is subject to the Cisco End User License Agreement (EULA) and any relevant supplemental terms (SEULA) found at http://www.cisco.com/c/en/us/about/legal/cloud-and-software/software-terms.html. You hereby acknowledge and agree that certain Software and/or features are licensed for a particular term, that the license to such Software and/or features is valid only for the applicable term and that such Software and/or features may be shut down or otherwise terminated by Cisco after expiration of the applicable license term (e.g., 90-day trial period). Cisco reserves the right to terminate any such Software feature electronically or by any other means available. While Cisco may provide alerts, it is your sole responsibility to monitor your usage of any such term Software feature to ensure that your systems and networks are prepared for a shutdown of the Software feature. % Failed to initialize nvram cisco CSR1000V (VXE) processor (revision VXE) with 2186344K/3075K bytes of memory. Processor board ID 9MJXF16X1D5 1 Gigabit Ethernet interface 32768K bytes of non-volatile configuration memory. 3985000K bytes of physical memory. 20357119K bytes of virtual hard disk at bootflash:. 0K bytes of WebUI ODM Files at webui:. %INIT: waited 0 seconds for NVRAM to be available PARSER-ERROR: (3) unexpected stale csb (0) Press RETURN to get started! *Apr 29 01:40:23.543: %VUDI-6-EVENT: [serial number: 95Q6WXKH89K], [vUDI: CSR1000V:95Q6WXKH89K], A new vUDI has been generated *Apr 29 01:40:23.543: %VUDI-6-EVENT: [serial number: 95Q6WXKH89K], [vUDI: CSR1000V:95Q6WXKH89K], A new vUDI is generated for this new VM instance *Apr 29 01:40:23.795: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = csr1000v Next reboot level = ax and License = No valid license found *Apr 29 01:40:31.178: %IOSXE_RP_NV-3-NV_ACCESS_FAIL: Initial read of NVRAM contents failed *Apr 29 01:40:31.545: %SMART_LIC-6-AGENT_READY: Smart Agent for Licensing is initialized *Apr 29 01:40:35.510: %VUDI-6-EVENT: [serial number: 95Q6WXKH89K], [vUDI: ], vUDI initialization is now complete *Apr 29 01:40:35.608: %VUDI-6-EVENT: [serial number: 9MJXF16X1D5], [vUDI: CSR1000V:9MJXF16X1D5], A new vUDI has been generated *Apr 29 01:40:35.608: %VUDI-6-EVENT: [serial number: 9MJXF16X1D5], [vUDI: CSR1000V:9MJXF16X1D5], The current vUDI has been invalidated by UUID change *Apr 29 01:40:35.627: Step 3. deletion of NOT-in-use licenses *Apr 29 01:40:35.627: Step 4. deletion of in-use licenses *Apr 29 01:40:36.622: %VXE_THROUGHPUT-6-LEVEL: Throughput level has been set to 1000 kbps *Apr 29 01:40:36.622: %VXE_THROUGHPUT-2-LOW_THROUGHPUT: System throughput set to low default level 1000 kbps, system performance can be severely impacted. Please install a valid license, configure the boot level and reload, to switch to a higher throughput *Apr 29 01:40:37.590: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down *Apr 29 01:40:40.312: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan *Apr 29 01:40:40.648: %VOICE_HA-7-STATUS: CUBE HA-supported platform detected. *Apr 29 01:40:41.273: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up *Apr 29 01:40:41.273: %LINK-3-UPDOWN: Interface EOBC0, changed state to up *Apr 29 01:40:41.274: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up *Apr 29 01:40:41.274: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0, changed state to up *Apr 29 01:40:41.275: %LINK-3-UPDOWN: Interface LIIN0, changed state to up *Apr 29 01:40:41.275: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to down *Apr 29 01:40:41.296: %LICENSE-2-UDI_CHANGED: UDI of this instance changed from OLD: CSR1000V:95Q6WXKH89K to New: CSR1000V:9MJXF16X1D5 *Apr 29 01:38:26.318: %IOSXE-4-PLATFORM: R0/0: kernel: acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. *Apr 29 01:38:26.362: %IOSXE-4-PLATFORM: R0/0: kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 *Apr 29 01:38:26.362: %IOSXE-4-PLATFORM: R0/0: kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 *Apr 29 01:38:26.362: %IOSXE-4-PLATFORM: R0/0: kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 *Apr 29 01:38:26.362: %IOSXE-4-PLATFORM: R0/0: kernel: ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 *Apr 29 01:38:26.373: %IOSXE-3-PLATFORM: R0/0: kernel: Warning: unable to open an initial console. *Apr 29 01:38:26.474: %IOSXE-4-PLATFORM: R0/0: kernel: cpldha: loading out-of-tree module taints kernel. *Apr 29 01:40:42.983: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up *Apr 29 01:40:42.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up *Apr 29 01:40:42.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up *Apr 29 01:40:42.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down *Apr 29 01:40:43.718: %ONEP_BASE-6-SS_ENABLED: ONEP: Service set Base was enabled by Default *Apr 29 01:40:48.053: %VXE_THROUGHPUT-6-LEVEL: Throughput level has been set to 1000 kbps *Apr 29 01:40:48.054: %VXE_THROUGHPUT-2-LOW_THROUGHPUT: System throughput set to low default level 1000 kbps, system performance can be severely impacted. Please install a valid license, configure the boot level and reload, to switch to a higher throughput -Traceback= 1#2b16deea7734cdd71d9e529b157a1c75 iosd_shr_m_uk9_AAA_Core_crb:7FB9BF08C000+6AB3A9 :55DA65DA6000+585F10D iosd_shr_m_uk9_AAA_Core_crb:7FB9BF08C000+76B608 *Apr 29 01:41:02.837: %IOSXE_OIR-6-INSCARD: Card (rp) inserted in slot R1 *Apr 29 01:41:02.838: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0 *Apr 29 01:41:02.839: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0 *Apr 29 01:41:03.213: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up *Apr 29 01:41:03.301: %SYS-5-RESTART: System restarted -- Cisco IOS Software [Fuji], Virtual XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.8.1a, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2018 by Cisco Systems, Inc. Compiled Tue 03-Apr-18 18:43 by mcpre *Apr 29 01:41:03.544: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF *Apr 29 01:41:03.544: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF *Apr 29 01:41:04.214: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to up *Apr 29 01:41:04.643: %AN-6-AN_ABORTED_BY_MANUAL_CONFIG_DETECTED: Autonomic disabled due to detection of new configuration. *Apr 29 01:41:04.644: %AN-6-AN_ABORTED_BY_CONSOLE_INPUT: Autonomic disabled due to User intervention on console. configure 'autonomic' to enable it. *Apr 29 01:41:11.648: AUTOINSTALL: Obtain siaddr 192.168.122.1 (as config server) *Apr 29 01:41:11.648: AUTOINSTALL: Setting hostname Router from DHCP reply *Apr 29 01:41:19.696: %PNP-6-HTTP_CONNECTING: PnP Discovery trying to connect to PnP server http://72.163.8.46/pnp/HELLO CRYPTO_PKI: setting trustpoint policy for TP-self-signed-1946761635 to specify TP-self-signed-1946761635 keypair usage% Generating 2048 bit RSA keys, keys will be non-exportable... *Apr 29 01:41:23.480: %PKI-2-NON_AUTHORITATIVE_CLOCK: PKI timers have not been initialized due to non-authoritative system clock. Ensure system clock is configured/updated. [OK] (elapsed time was 1 seconds) *Apr 29 01:41:24.975: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-1946761635 has been generated or imported *Apr 29 01:41:24.976: %SSH-5-ENABLED: SSH 1.99 has been enabled *Apr 29 01:41:25.040: %PKI-4-NOCONFIGAUTOSAVE: Configuration was modified. Issue "write memory" to save new IOS PKI configuration *Apr 29 01:41:25.108: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-1946761635.server has been generated or imported Router> Router>en Router# Router# Router#sh ver Cisco IOS XE Software, Version 16.08.01a Cisco IOS Software [Fuji], Virtual XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.8.1a, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2018 by Cisco Systems, Inc. Compiled Tue 03-Apr-18 18:43 by mcpre Cisco IOS-XE software, Copyright (c) 2005-2018 by cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. ROM: IOS-XE ROMMON Router uptime is 1 minute Uptime for this control processor is 3 minutes